Factory Tracking: A Work Order, Named Stages, and Scrap With a Reason
1 Nov 2026
A factory knows where a work order stands when quantity moves through stages you name, and scrap is recorded with a reason rather than with an invented efficiency ratio. Materials and their movement sit in the inventory guide. This page is the production floor.
A factory owner asks in the afternoon where this work order stands, how much left in good condition, and how much was scrap. If the answer is on paper with the shift lead, it arrives late and disagrees with the paper at the next stage. Production tracking makes the work order a record that quantity moves on: entered a stage, left it as good output, or left it as scrap with a reason. There is no global ratio board, and no efficiency number invented so the plant looks measured.
Stages are names you set, because your line is not your neighbor line. Cutting, then assembly, then finish, is an illustration, not a list imposed here. Your stages may be mixing and packing only. The screen shows what you named. A stage with no real name becomes an empty column people skip, and the report lies. Start with the stages where a supervisor actually stands and asks a question.
The work order
- An order number, a finished item, and a quantity required.
- An open date, and the customer or warehouse asking for the quantity if that matters.
- The current stage and the quantity that entered it.
- Quantity that left in good condition to the next stage or to the store.
- Scrap quantity with a reason and the stage where it happened.
Good quantity plus scrap does not have to match the input on day one if your count is still rough, but the gap must show rather than be settled in silence. Silent settlement is how scrap disappears from the report and returns at month end as a material shortage. A visible field is better than a number that balances by being untrue.
Scrap is a reason, not a ratio
Scrap is a quantity at a stage, with a reason from a list you write: bad material, an operating mistake, a setup trial, or another reason you actually use. A short list gets used. A long list is ignored and the reason becomes "other" every time. These quantities are not turned into an overall effectiveness percentage, and the screen is not promised to raise output. It makes the question "where did the gap go" answerable from the record rather than from memory.
The person who records scrap is not always the person who closes the work order. The stage lead enters the quantity. The person who confirms may be the shift manager at the end of the day or immediately, depending on the size of the line. Delay of confirmation is written as a rule so a stage is not closed before the quantity is seen. Closing a stage with no scrap recorded, while the floor knows scrap exists, brings back the secret notebook.
How production meets the store
Material that enters a work order leaves a balance, and good output may enter a finished-goods store. That is a stock movement. The inventory and sales guide explains balance, selling, and purchasing in the wider sense. This page does not repeat stocktaking. It assumes a work order should point at a material and a product so quantity is not written in the air. A full link, deducting a component from a formula, is extra scope when the formula is written and stable. Without a formula, deducting a component is a guess. Start by tracking the stage and the scrap, and add the formula when you trust the numbers going in.
The floor screen
The person on the line needs few controls: an open order, a stage, good quantity, scrap quantity, a reason. The device has to tolerate dust and stay away from water if that is the room, and that is a place requirement rather than a drawing style. The report the office sees at the end of the day is built from those controls. A report filled in the office from a phone call is not production tracking. It is dictation. The difference shows when you compare the supervisor paper with the screen record for a week.
What we ask before a walk on the line
- Stage names in the order the floor uses.
- One work order from this week with a quantity and scrap.
- The scrap reasons the supervisor uses today.
- Whether the formula is written or material is drawn by estimate.
- Who on the line will press the screen and who reviews the day.
Line questions
Does the system schedule machines?
Not in the first version. Knowing where an order stands comes before assigning machines. Scheduling is a later scope, once stages are actually closed on the record and not on paper.
Do you show a completion ratio?
Good quantity against quantity required is a simple figure that can be shown, because it is subtraction rather than an invented index. Any efficiency ratio that mixes machine uptime, quality, and speed is not built here and is not claimed as an output of the system.
Are old work orders imported?
Orders open this week are worth entering because they still move. Last year paper archive is not imported as a block. A sample is enough if the debate is about fields, and then you continue forward.
The record is built from custom software development. Material movement in the wider sense is in the inventory and sales guide.
Write the stage names through start your project. The WhatsApp button below the page fits the stage names as the floor calls them.
